Sir Frank Whittle - Coventry - Statues of Historic Figures on Waymarking.com

Whittle was born in a terraced house in Earlsdon, Coventry, England, United Kingdom on 1 June 1907, the son of a mechanic. When Whittle was nine years old, the family moved to the nearby town of Royal Leamington Spa, where his father started an engineering factory. He left Leamington College in 1923 to join the RAF. Through his early days as an Aircraft apprentice (first at RAF Cranwell but latterly at RAF Halton) he maintained his interest in the Model Aircraft Society where he built replicas, the quality of which attracted the eye of his commanding officer, who also felt that Whittle was a mathematical genius.

He was so impressed that he recommended Whittle for officer training at the RAF College, Cranwell in Lincolnshire in 1926, a rarity for a "commoner" in what was still a very class-based military structure. For Whittle this was the chance of a lifetime, not only to enter the officer corps but also because the training included flying lessons. Of the few apprentices that were accepted, only about one percent completed the course. Whittle was the exception to the rule, graduating in 1928 at the age of 21, ranked second in his class in academics and an "Exceptional to Above Average" pilot.

Another requirement of the course was that each student had to produce a thesis for graduation. Whittle decided to write his thesis on future developments in aircraft design, notably high-speed flight at high altitudes and speeds over 500 mph (800 km/h). He showed that incremental improvements in existing propeller engines were unlikely to make such flight routine. Instead he described what is today referred to as a motorjet, a motor using a conventional piston engine to provide compressed air to a combustion chamber whose exhaust was used directly for thrust – essentially an afterburner attached to a propeller engine. The design was not a new one, it had been talked about for some time in the industry but Whittle's interest was to demonstrate that at increased altitudes the lower outside air pressure would increase its efficiency. For long-range flight, using an Atlantic-crossing mailplane as his example, the engine would spend most of its time at high altitude and thus could outperform a conventional powerplant.



Development of the jet engine
Whittle continued working on the motorjet principle after his thesis work and eventually abandoned it when further calculations showed it would weigh as much as a conventional engine of the same thrust. While thinking about the idea he thought "Why not substitute a turbine for the piston engine?" Instead of using a piston engine to provide the compressed air for the burner, a turbine could be used to extract some power from the exhaust and power a compressor, like those used for superchargers. The leftover exhaust thrust would power the aircraft.

Earlier, in July 1926, A. A. Griffith published a paper on compressors and turbines, which he had been studying at the RAE. He showed that such designs up to this point had been flying "stalled", and that by making the compressor blades into an aerofoil shape, their efficiency could be dramatically improved. The paper went on to describe how the increased efficiency of these sorts of compressors and turbines would allow a jet engine to be produced, although he felt the idea was impractical, and instead suggested using the power as a turboprop. At the time most superchargers used a centrifugal compressor, so there was limited interest in the paper.

In late 1929 Whittle sent his concept to the Air Ministry to see if it would be of any interest to them. With little knowledge of the topic they turned to the only other person who had written on the subject and passed the paper on to Griffith. Griffith appears to have been convinced that Whittle's "simple" design could never achieve the sorts of efficiencies needed for a practical engine. After pointing out an error in one of Whittle's calculations, he went on to comment that the centrifugal design would be too large for aircraft use and that using the jet directly for power would be rather inefficient. The RAF returned comment to Whittle, where they referred to the design as "impracticable."

Others in the RAF were not so sure. In particular Johnny Johnson convinced him to patent the idea in January 1930. Since the RAF was not interested in the concept they did not declare it secret, which meant that Whittle was able to retain the rights to the idea, which would have otherwise been the property of the RAF. This rejection would later turn out to be a stroke of luck.

Meanwhile Whittle moved onto the Officers' Engineering Course at RAF Henlow, Bedfordshire in 1932 and then to Peterhouse, a college of Cambridge University, in 1934, graduating in 1936 with a First in the Mechanical Sciences Tripos.



Power jets
Whittle's jet engine patent lapsed in 1935 because he could not afford the renewal fee of £5. Soon after this he was approached by two ex-RAF men, Rolf Dudley-Williams and James Collingwood Tinling, who wanted to expand the development of his engine. The three incorporated as Power Jets Ltd. in 1936 with a bank loan of £2,000. Work was started on an experimental engine at a factory in Rugby, Warwickshire belonging to British Thomson-Houston, a steam turbine company. The RAF still saw no value in the effort but although Whittle was still a pilot they placed him on the Special Duty List and agreed to allow him to work on the design as long as it took no more than six hours a week.


The Gloster E.28/39, the first British aircraft to fly with a turbojet engineFunding development of the first engine, known as the WU (Whittle Unit) was a serious problem. Although privately funded, most potential investors shied from a project that appeared to be semi-secret yet had no RAF (Royal Air Force) backing. Something seemed to be amiss; if the project was going to work, why didn't the RAF fund it? Once again it seemed not everyone was so sceptical of Whittle's ideas and in October 1936 Henry Tizard, the rector of Imperial College London and chairman of the Aeronautical Research Committee, sent details of Whittle's engine to Griffith once again. Griffith had by this time started construction of his own engine design; perhaps in order to avoid tainting his efforts, he returned a much more positive review. He remained highly critical of some features, notably the use of jet thrust, seemingly ignoring the fact that its performance at high speed and altitude was the crucial aspect of the programme.

Even with these problems Power Jets were able to complete the WU, which ran successfully on April 12, 1937. Tizard pronounced it "streets ahead" of any other advanced engine he had seen and managed to interest the Air Ministry enough to fund development with a contract for £6,000 to develop a flyable version. Nevertheless it was a year before all of the funds were available, greatly delaying development.

Meanwhile testing continued with the WU, which showed an alarming tendency to race out of control. Due to the dangerous nature of the work being carried out, in 1938 development was largely moved from Rugby to the BTH's semi-disused Ladywood foundry at nearby Lutterworth in Leicestershire. There was a successful run of the WU there in March 1938. Although the potential of the engine was obvious, the Air Ministry remained focused on the production of piston engine designs.

All of these delays and the lack of funding slowed the project. In Germany, Hans von Ohain had started work on a prototype in 1935[citation needed] and had by this point passed the prototype stage and was building the first flyable design,[citation needed] the Heinkel HeS 3. There is little reason to believe that Whittle's efforts would not have been at the same level or more advanced had the Air Ministry taken a greater interest in the design. When the war started in September 1939, Power Jets had a payroll of only 10 and Griffith's efforts at the RAE and Metropolitan Vickers were similarly small.

The stress of the continual on-again-off-again development and problems with the engine had a serious toll on Whittle. He suffered from stress-related ailments such as eczema and heart palpitations, while his weight dropped to 9 stone (126 pounds/57 kg). In order to keep to his sixteen-hour workdays, he sniffed Benzedrine during the day and then took tranquilizers and sleeping pills at night to offset the effects and allow him to sleep. Over this period he became irritable and developed an "explosive" temper.

Following the outbreak of World War II the Air Ministry changed priorities and once again looked at the various advanced projects underway. By 1939, Power Jets could barely afford to keep the lights on when yet another visit was made by Air Ministry personnel. This time Whittle was able to run the WU at high power for 20 minutes without any difficulty. One of the members of the team was the Director of Scientific Research, H. E. Wimperis, who walked out of the demonstration utterly convinced of the importance of the project.

A contract for full-scale development was immediately sent to Power Jets, along with a number of tenders to various companies to set up production lines for up to 3,000 engines a month in 1942. Power Jets had no manufacturing capability, so the Air Ministry offered shared production and development contracts with BTH, Vauxhall and Rover. However, the contract was eventually taken up by Rover only. They also sent out a contract for a simple airframe to carry the engine, which was quickly taken up by Gloster.

Whittle had already studied the problem of turning the massive WU into a flyable design and with the new contract work started in earnest on the "Whittle Supercharger Type W.1." However, Rover was unable to deliver the W.1 production engine before Gloster's experimental airframe was ready. Whittle then cobbled together an engine built from various test parts and called it the W.1X (the X standing for experimental), which ran for the first time on December 14 1940. This engine powered the Gloster E.28/39 for taxi testing in Gloster, near the factory, when it took to the air for two or three short hops of several hundred yards and about 6 foot from the ground on April 7 1941.

The "full" W.1 of 3.8 kN (850 lbf) thrust ran on April 12, 1941 and on May 15, 1941 the W.1-powered E.28/39 took off from Cranwell at 7.40 pm, flying for seventeen minutes and reaching a maximum speed of around 340 mph(545 km/h). Within days it was reaching 370 mph (600 km/h) at 25,000ft (7,600 metres) exceeding the performance of the contemporary Spitfires. Success of the design was now evident to all and nearly every engine company in Britain started their own crash efforts to catch up with Power Jets.


The W2/700 engine flew in the Gloster E.28/39, the first British aircraft to fly with a turbojet engine, and the Gloster Meteor.A newer design known as the W.2 was then started. Like the W.1 it featured a "reverse flow" design of the burners, in which the heated air from the flame cans was piped back towards the front of the engine before entering the turbine area. This allowed the engine to be "folded", with the flame cans lying around the turbine area, and therefore making for a shorter engine.

Power Jets also spent some time in May 1940 drawing up the W.2Y, a similar design with a "straight through" airflow that resulted in a longer engine and (more critically) driveshaft but with a somewhat simpler layout. In order to reduce the weight of the driveshaft as much as possible, the W.2Y used a large cylindrical shaft almost as large as the turbine disk, "necked down" at either end where it connected to the turbine and compressor.

The Air Ministry was eager to obtain an operational jet aircraft and authorised BTH to press ahead with a twin-engined jet interceptor, which would evolve into the Gloster Meteor. The Meteor was intended to use either the W.2 or the similar Halford H.1 (later named "Goblin") but de Havilland later decided to keep all the Halfords for their design, the de Havilland Vampire.



Rover
In 1941 Rover set up a new laboratory for Whittle's team along with a production line at their disused Barnoldswick factory but they also set up a parallel effort with their own engineers at Waterloo Mill, Clitheroe. Here Adrian Lombard attempted to develop the W.2 into a production quality design, dispensing with Whittle's "reverse flow" burners and developing a longer but simpler "straight-through" engine instead. Work at Barnoldswick continued on Whittle's original design, now known as the W.2B/23, while Lombard's new design became the W.2B/26. Whittle was upset by this course of events, feeling that all work should concentrate on producing a single design as soon as possible.

By late 1941 it was obvious to all that the arrangement between Power Jets and Rover was not working. Whittle was frustrated by Rover's inability to deliver production-quality parts, as well as with their "we know better than you" attitude and became increasingly vocal. Rover was losing interest in the project after the delays and constant harassment from Power Jets.



Rolls-Royce
In 1940, Stanley Hooker of Rolls-Royce had met with Whittle and later introduced him to the current CEO of Rolls-Royce, Ernest Hives. Hooker led the supercharger division at Rolls-Royce, which was naturally suited to jet engine work. Hives agreed to supply key parts to help the project and it was Rolls engineers who helped solve the surging problems seen in the early engines. In early 1942 Whittle contracted Rolls for six engines as well, known as the WR.1, identical to the existing W.1.

The problems at Rover became a "public secret" and eventually Spencer Wilkes of Rover met with Hives and Hooker at the Swan and Royal pub near the Barnoldswick factory. They decided to trade the jet factory at Barnoldswick for Rolls' tank engine factory in Nottingham. A handshake sealed the deal. The handover took place on January 1 1943, although the official date was later. Rolls soon closed Rover's parallel plant at Clitheroe, although they continued development of the W.2B/26 that had been developed there.

Testing and production was immediately stepped up. In December Rover had tested the W.2B for a total of 37 hours but within the next month Rolls-Royce tested it for 390 hours. The W.2B passed its first 100 hour test at full performance of 725 kgf (7.11 kN) on May 7, 1943. The prototype Meteor airframe was already complete and took to the air on June 12, 1943. Production versions started rolling off the line in October, first known as the W.2B/23, then the RB.23 (for Rolls-Barnoldswick) and eventually the Rolls-Royce Welland. Barnoldswick was too small for full-scale production and turned back into a pure research facility under Hooker, while a new factory was set up in Newcastle-under-Lyme.

Info from inside museum

URL of the statue: Not listed

Visit Instructions:
You must have visited the site in person, not online.

Recent Visits/Logs:

Date Logged Log User Rating   05/08/2015 greysman visited it 03/23/2014 Jay&R visited it 08/05/2013 vix92008 visited it 08/05/2013 Angelina Ballerina visited it 02/08/2011 grnoval visited it 08/06/2010 scion101 visited it 08/14/2008 Superted visited it 08/11/2008 samanthajune visited it 04/17/2008 ptr.dvorak visited it

View all visits/logs